Saturday, 6 January 2018

// // Leave a Comment

UTU Power Electronics 2012 Paper | B.Tech 6th Sem

UTU B.Tech Previous year exam paper of POWER ELECTRONICS 2012, 6th semester 


POWER ELECTRONICS
SEM-VI, 2012
B.TECH EXAMINATION
UTTARAKHAND TECHNICAL UNIVERSITY

Time: 3 Hours
Total Marks: 100
Note: Attempt all question. Use of calculator is permitted.

Answer any four parts of the following:
  1. What are the different methods of firing employed for SCR triggering? Explain UJT firing circuit with relevant waveforms.
  2. Discuss the two transistor model of thyristor and derive an expression for the anode current.
  3. Draw the static V-I characteristics of SCR and explain its mode of operation.
  4. Name the different power electronic converters available and list their advantages over conventional modes of conversion and control.
  5. What are the characteristics of n ideal power switching device? Compare the characteristics of IGBT and MOSFET.
  6. Draw & Explain the circuit diagram for turning on & Turning off operation of a G.T.O.
Answer any four parts of the following:
  1. Define di/dt and dv/dt rating of SCR. How is SCR protected against these?
  2. For what type of protection a snubber circuit is used and discusses the design of snubber circuit.
  3. A number of SCRs, each of rating 2000 V and 50A, are to be used in series-parallel combination in a circuit to handle 11Kv and 400A. For a derating factor of 0.15, calculate the number of SCRs in series and parallel units. The maximum difference in their reverse recovery charge in 20μC. Calculate the value of dynamic equalizing capacitance.
  4. The resonant pulse communication circuit has C = 20μF and L = 5μH. Initial voltage across capacitor is Vs = 230V. For a constant load current of 300A, calculate
    (a) Conduction time for the auxiliary thyristor
    (b) Voltage across the main thyristor when it gets commutated and
    (c) The circuit turn off time for the main thyristor.
  5. Give the working of step down chopper and derive expression for output voltage.
  6. A step up chopper has input voltage of 220V and output voltage of 660 V. If the conducting time of thyristor-chopper is 100μs, compute the pulse width of output voltage. In case output voltage pulse width is halved for constant frequency operation, find the average value of new output voltage.
Answer any two parts of the following:
  1. Discuss the working of single phase full wave ac-dc convertor taking into account the effect of source inductance. Draw the output voltage waveform for firing angle 30o if overlap angle is 15o for zero degree firing angle.
  2. A 3-phase full converter, fed from 3-phase, 400V, 50 Hz source, is connected to load R = 10, E = 350 V and large inductance so that output current is ripple free. Calculate the power delivered to load and input pf for
    (a) firing angle of 30o and (b) firing advance angle of 60o.
  3. For a 3-phase semi converter, draw the output voltage waveform for a firing angle delay of 90o indicating the conduction of its various elements on the assumption of continuous output current. Discuss whether freewheeling diode comes into play or not. Also obtain the expression for output voltage.
Answer any two parts of the following:
  1. Describe the operation of a single phase full wave ac regulator feeding a resistive load. Also derive the expression for output voltage.
  2. A six pulse cycloconverter, fed from 3-phase, 400V, 50 Hz source, is delivering a load current 40 A to a 1-phase resistive load. The source has an inductance of 1.2 mH per phase. Calculate the RMS value of load voltage for firing angle delays of
    (a) 0o
    (b) 30o
  3. Describe the principle of working of single phase to single phase step down cycloconverter both continuous and discontinuous conditions for a bridge type cycloconverter.
Answer any two parts of the following:
  1. Discuss the principle of working of a three phase bridge inverter with an appropriate circuit diagram. Draw phase & line voltage waveforms on the assumption that each thyristors conducts for 180o and the resistive load is star connected. The sequence of firing of various SCRs should be indicated in the diagram.
  2. Describe how multiple pulse waves can be generated from carrier and reference waves. Hence show that
    (a) Number of pulses per half cycle, N = ωc/2ω
    (b) Pulse Width 2d/N = (1 - Vr/Vc)π/n
    where Vc & Vr are the amplitudes of carrier and reference signals respectively.
  3. For a single phase full bridge inverter, Vs = 230 V dc, T = 1ms. The load consist of RLC in series with R = 1, ωL = 6Ω and 1/ωC =7Ω
    (a) Sketch the waveform for load voltage VO fundamental component of load current i, source current is and voltage across thyristor. Indicate the device under conduction during different Interval of one cycle.
    (b) Find the power delivered to load due to fundamental component.

How to use this UTU paper

This UTU Power Electronics 2012 Paper | B.Tech 6th Sem resource is useful for understanding Uttarakhand Technical University question patterns for 6th sem, 2012 exam. Review the repeated units, important numerical questions, definitions and long-answer topics before making your revision plan. Compare this paper with nearby semester papers to identify common subjects and frequently asked concepts.

For more related downloads, browse 3rd Year Papers, 3rd Year Papers, and 4th Year Papers.

Read More
// // Leave a Comment

UTU System Engineering 2012 Paper | B.Tech 5th Sem

UTU B.Tech Previous year exam paper of SYSTEM ENGINEERING 2012, 5th semesterSYSTEM ENGINEERING

SEM-V, 2011-12
B.TECH EXAMINATION
UTTARAKHAND TECHNICAL UNIVERSITY

Time: 3 hours
Total Marks: 100
Attempt any four parts:
  1. What is open loop and closed loop system? Giveadvantages and disadvantages of closed loop control system.
  2. Explain force-voltage analogy with relevant diagram andequations.
  3. Draw f-i analog system of Fig. 1.
    SYSTEM ENGINEERING
    Figure. 1
  4. Determine the transfer function C/R from the system shown in Fig. 2, using block diagram reduction technique.
    SYSTEM ENGINEERING
    Figure . 2
  5. Represent the following set of equation by a signal flow graph and determine the overall gain relating x and x using Mason's gain formula.
    x = ax1 + fx2          x = bx2 + ex4
    x = cx3 + hx5         x = dx4 + gx2
  6. For the following mechanical system shown in Fig. 3.
    (a) Draw free body diagram
    (b) Write the system dynamic equations
    (c) Draw electrical analogous circuit
    SYSTEM ENGINEERING
    Figure.3
Attempt any four parts:

  1. Derive expression for time response of second order control system for unit step input.
  2. When a second order control system is subjected to a unit step input, the values of ξ= 0.5 and ωn = 6 rad/sec. Determine the rise time, and peak overshoot
  3. For the system shown in Fig.4. Determine Kp and ess for unit step input.
    SYSTEM ENGINEERING
    Figure.4
  4. What are dynamic error coefficients?
  5. Classify the various types of controllers; also discuss in brief PID control action.
  6. A unity feedback system is characterized by an open loop transfer function.
    UTTARAKHAND TECHNICAL UNIVERSITY (UTU)
    Determine the gain K so that the system will have a damping ration of 0.5. For this value of K determine settling time and peak time for a unit step input.
Attempt any two parts:
  1. Explain sampler, sampling process, sampling theorem and zero-order-hold-circuit used in sampled data control system.
  2. Explain any five properties of z-transformation and solve the difference equation c(k+2)+3c(k+1)+2c(k)=u)k; c(0)=1 and c(k)=0 for k<-1.
  3. Determine the pulse transfer function and stability for the system shown in fig.5, for
    (a) T = 0.5 sec
    (b) T = 1.0 sec
    UTTARAKHAND TECHNICAL UNIVERSITY (UTU)
    Figure.5
    What conclusion is obtained from the results of (a) and (b)?
Attempt any two parts:
  1. How Diagonalization is done in discrete control system? Write down model matrix and diagonal matrix for the system having coefficients matrix.
    UTTARAKHAND TECHNICAL UNIVERSITY (UTU)
  2. Write down properties of state transition matrix. Obtain the time response of the system given below.
    x = ax
    WhereUTU System Engineering 2012 Paper | B.Tech 5th Sem question paper given x(0) = [1  1]T And UTU System Engineering 2012 Paper | B.Tech 5th Sem question paper
  3. Check the controllability and observability of a system having following coefficient matrices.
    UTTARAKHAND TECHNICAL UNIVERSITY (UTU)
Attempt any two parts:
  1. What is purpose of linearization? Describe the linearization process of a non-linear state model.
  2. How stability of non linear system is checked by Liapunov's stability criteria? Consider a non linear system is described by the equation
    x1 = x2
    x2 = - x2 – x13
    Check the stability of the system by Liapunov's method.
  3. Construct a Liapunov's function for the following system using variable gradient method and examine stability of the following system
    x1 = -x1 - 2x12 x2
    x2 = -x2

How to use this UTU paper

This UTU System Engineering 2012 Paper | B.Tech 5th Sem resource is useful for understanding Uttarakhand Technical University question patterns for 5th sem, 2012 exam. Review the repeated units, important numerical questions, definitions and long-answer topics before making your revision plan. Compare this paper with nearby semester papers to identify common subjects and frequently asked concepts.

For more related downloads, browse 3rd Year Papers, 3rd Year Papers, and 4th Year Papers.

Read More
// // Leave a Comment

UTU Fundamentals of Electronics 2012 Paper | B.Tech 1st Sem

Fundamental of ElectronUTU B.Tech Previous year exam paper of Fundamental of Electronics Engineering 2012, 1st semesterics Engineering


Uttarakhand Technical University
B.tech (first year)
odd sem Examination, 2012,
Fundamental of Electronics
Engineering

time :- 3 hrs}
[Total Marks :100 ]
Note : Use of calculator is permitted. 

                                                              Section A

Q1:- Answer any 4 parts of the following :
 4*5=20
  1. Explain intrinsic and extrinsic semiconductors by stating at least two examples of each.
  2. Explain the basic concept of forbidden gap in semi conductors and discuss the effect of temperature on it.
  3. Describe the formation of a p-n junction . Explain the depletion region and potential barrier.
  4. Explain what do you understand by clipping circuit. Describe the working of the positive clipper.
  5. Show that IE =IB + αIE + ICBO .   In what way  ICBO  depend on temperature.
  6. Explain the binary numbers . Taking 125.525 as an example, describe decimal to binary conversion.
Q2:- Attempt any four parts of the following :
4*5=20
  1. Explain with the help of suitable diagram, how free electrons and holes contribute towards the electric current in a semiconductor.
  2. Describe how n-type and p-type semi conductors are produced. State the main difference between them.
  3. What do you understand by dc and ac resistance of a crystal diode. How will you find them using V-I characteristic.
  4. Describe the various rating of Zener diode supplied by manufactures.
  5. Calculate ac drain resistance , transconductance and amplification factor of a JFET with the help of following experimentally obtained data.VGS      0V                0V               -0.2V
    VDS      7V                15V              15V
    I
    D       10mA             10.25mA        9.65mA
  6. Draw the circuit of a practical single stage transistor amplifier. Explain the function of each     component.
Q3:- Attempt any two parts of the following :
2*10=20
  1.  Describe half-wave rectifier and obtain an expression for the rectification efficiency of the half-wave rectifier is used to supply 12V dc to a resistive load RL =500Ω. If the forward resistance of diode rf  is 25Ω , find the rms value of ac voltage supplied to the circuit.
  2. Explain the CB configuration of a transistor and draw its input and output characteristics.Describe      current amplification factor α collector current IC , input resistance ri and output resistance ro.
  3. Draw the equivalent circuit of an ideal and actual zener diode. Explain V-I characteristics of a zener diode. Describe how it can be used as a shunt regulator.

Q4:- Attempt any two parts of the following :
2*10=20
  1. Describe the construction and operating principle of JFET. State the advantage of JFET.  A JFET has a drain current of 5 mA . If  IDSS = 10 mA and VGS(OFF) = -6V,calculate the value of VGS and pinch off voltage VP.
  2. Explain the need of transistor biasing circuit and state its essential requirements. Obtain the      expression for the stability factor S for CE configuration.
  3. Draw an ac equivalent circuit of a single stage common emitter transistor amplifier and expression      for the voltage gain and power gain . An amplifier has an open circuit gain of 1000, an output resistance of 15Ω  and an input resistance of 7 KΩ  . It is supplied from a signal source of e.m.f 10 mV and internal resistance 3 KΩ . The amplifier feeds a load of 35Ω. Calculate the output voltage and power gain.

Q5:- Attempt any four parts of the following :
2*10=20
  1.  What do you understand by an ideal operational amplifier ? Describe its characteristics and discuss lts limitations.In an op-amplifier ,the amplifier gain is 10000. The input series resistance feedback resistance are 100 KΩ and 500 KΩ respectively. If the input voltage is 1.0V, calculate output voltage. 
  2. Describe NAND gate and NOR gate and discuss their characteristics. Explain why these are called as universal building blocks.
  3. Describe the single variable theorem of Boolean algebra. With the help of truth tables, explain     associative and distributive laws.

How to use this UTU paper

This UTU Fundamentals of Electronics 2012 Paper | B.Tech 1st Sem resource is useful for understanding Uttarakhand Technical University question patterns for 1st sem, 2012 exam. Review the repeated units, important numerical questions, definitions and long-answer topics before making your revision plan. Compare this paper with nearby semester papers to identify common subjects and frequently asked concepts.

For more related downloads, browse 1st Year Papers, 3rd Year Papers, and 4th Year Papers.

Read More

Friday, 5 January 2018

// // Leave a Comment

UTU Electromechanical Energy Conversion 2012 | 3rd Sem

UTU B.Tech Previous year exam paper of FUNDAMENTALS OF ELECTROMECHANICAL ENERGY CONVERSION-I 2012, 3rd sem



UTTARAKHAND TECHNICAL UNIVERSITY
B.TECH (SEM. 3RD) 2012
ELECTROMECHANICAL ENERGY CONVERSION-I

Time : 3hr
max marks: 100
Note : Attempt all questions.
SECTION A
Q1:- Attempt any four of the following :    
   4 x 5=20 
1)    Show that the energy stored in a magnetic field is equal to the area between the ψ-i curve for the system and the flux linkage (ψ) axis.
2)     2.    Show that the field energy in a linear magnetic system is given by:-      Wf = ½ Li2 = ½ ψi = ½L ψ²
3)     Distinguish between singly excited and doubly excited systems.
4)     For a singly linear magnetic system, derive an expression for the electromagnetic torque.
5)    Define field energy and coenergy.
6)     Why most practical energy conversion devices use magnetic field as the coupling medium between electrical and mechanical system?

SECTION B
 Q2:- Attempt any four of the following :   
4 x 5=20 

1.     What do you understand by demagnetizing and cross magnetizing effects of armature reaction in a d.c machine.
2.     Derive the e.m.f and torque equations for d.c machines.

3.     Explain clearly the functions of the following in d.c machines:
(a) interpoles (b) compensating windings

4.     What are the various possible cause for d.c shunt generator not building up voltage ?
5.     What are the difference types of d.c generators according to the ways in which fields are excited? Show the connection diagram of each type.
6.     A 4 pole generator with wave wound armature has 51 slots each having 48 conductors. The flux per pole is 7.5 mWb. At what speed must the armature be driven to give an induced emf of 440V


SECTION C

Q3:- Attempt any two parts of the following :                                                                                 10 x 2=20 

1.  A 4 pole, d.c. shunt motor has a flux per pole of 0.04 Wb and the armature is lap wound with 720 conductors. The shunt field resistance is 240 ohm and the armatureresistance is 0.2 ohm. brush contact drop is 1V per brush. Determine the speed of the machine when running as:
(a) A motor taking 60 A
(b) A generator supplying 120 A. The terminal voltage in each case is 480 V.

2.     What are the drawbacks of a 3 point starter? Describe a 4 point starter with a neat sketch.3.     Describe the test conducted on d.c motors in which the temperature rise and the commutation conditions can be checked under rated load condition such that only losses are being supplied by the power supply. 
x




SECTION D
 Q4:- Attempt any two parts of the following :
     10 x 2=20   

1.     Explain Sumpner's test for testing two single phase transformers. What is the main advantage of this test over Open circuit and Short circuit tests conductance on single phase transformers?
2.     The HV terminals of a 3 phase bank of three single phase transformers are connected to a 3 wire ,3- ɸ, 33 kV(LL) system. The LV terminals are connected to a 3 wire ,3- load rated 1800 kVA and 2500 V(LL). Specify the voltage,current and kVA ratings of each transformer (both HV and LV windings ) for the following connections             (a) Y-Y  (b) Δ-Δ  (c) Y-Δ  (d) Δ-Y
3.     Derive an expression for saving in conductor material in an autotransformer over a two winding transformer of equal rating. State its advantages and disadvantage over two winding transformer.

SECTION E

.Q5:- Attempt any two parts of the following :
10 x 2=20 

1.     In open delta transformer,show that the secondary line voltages from a balanced three phase system of voltages,in case the supply voltage are balanced.
2.     Two 1 phase Scott connected transformers supply a 3 phase, 4 wire system with 231 V between the lines and the neutral. The HV windings are connected to a 2 phase system with a phase voltage of 6000 V. Determine the number of turns in each section of HV and LV windings and the position of the neutral point if the induced voltage per turn is 8 V.
3.     What are the condition for satisfactory operation of 1 phase transformer? Deduce an expression for the load shared by two transformers in parallel when no- load voltages of these transformers are not equal. What will be the load distribution if the voltage ratio is exactly equal ?



How to use this UTU paper

This UTU Electromechanical Energy Conversion 2012 | 3rd Sem resource is useful for understanding Uttarakhand Technical University question patterns for 3rd sem, 2012 exam. Review the repeated units, important numerical questions, definitions and long-answer topics before making your revision plan. Compare this paper with nearby semester papers to identify common subjects and frequently asked concepts.

For more related downloads, browse 2nd Year Papers, 3rd Year Papers, and 4th Year Papers.

Read More